Search the Community
Showing results for tags 'configuration'.
Found 9 results
-
Hi, About SmartSlice: „Smart Analog I/O performs data pre-processing to help you reduce PLC programming. Scaling and alarms, and even totalising or rate-of-change calculations are handled inside the unit.” How to get to this honey in case of GRT1-ECT bus coupler and NJ101 EtherCAT communication? What means “Configuration Tool” in W18E-EN-02 “GRT1-series EtherCAT Communication Unit Operation Manual”?
-
Hi everyone, I have a question for you all, Is possible to configure CJ2M-CPU11 with tags trough network configurator to connect Control Logix PLC using EthernetIP? I did a configuration with CJ2M-CPU31 and Control Logix PLC with no problem, but now I need to communicate CJ2M-CPU11 with Control Logix PLC using EthernetIP. Some of you did this configuration between this two PLC before? Regards!
-
I have several machines that use the RJ71EIP91 module. I have not had any issues until now. I do not have the original apa file. I upload the configuration and try to restore it from the configuration.apa file, it does not show everything that is connected to the card or programmed in the PLC. when I verify this it says that the configuration is a mismatch. I have several of these scattered throughout the factory and I don't have this problem anywhere else. Is there a solution to this problem?
-
Hi All, I just start to setup a rotary servo (rotary transmission load type) and the designer pass me the spec of gear ratio 1:100. In my motion scaling page, I set Transmission I:O as 1:100 and then scaling unit is just position unit with 1:1. However, when i jog my rotary servo, it does not reflect the actual position in degree, so I went to read through the manual but still cant quite get how should i configure my scaling so that I can see that when the motor is rotating, i can see it rotate how many degrees? I try to set scaling 360 degree to 1.0 load rev, and the position feedback seems like much more finer....
-
Hi every one, One of my machine i have to fix , has simatic pc unit installed that causing too much trouble and client want to replace it with simple pc with additional profibus card installed in PCI slot, is there any way to configure image of simatic pc in new simple pc
-
Hi, I've got a very old version of Wonderware, version 9.5, which isn't going to be upgraded anytime soon. I would like to configure a button to perform 2 tasks under "Touch Pushbuttons", ideally "Action" and "Show Window". I am unable to enable both at the same time, so I've been trying to write a script that would perform both functions, but so far unsuccessfully. Is this something that can be done, or is there another way to get around this problem? I would like the button to toggle a bit and to open another window with more controls. thanks
-
Hello All, Am a bit new to practical PLC applications. I was trying to configure a Phoenix Contact I/O module (1452916) on a MicroLogix 1100 PLC but it kept faulting out with the fault light RED. It would say "Major Error Halt S:1/13". The error description says I/O mismatch. The error code is 187h (see attachment). The Phoenix module has a cable with 19 pin positions for the 8 input. I connected the pin 17 and 18 to 24 volts and 0 volts respectively. Then because I was using input 5 I connected the pink wire to PLC input (I/1) 24volts and the White/Yellow wire to the PLC common. On the I/O configuration on RSLogix 500, I used "Other" ( See attachment) but did not know the vendor details. Could anyone help me with the steps on how to communicate with the module? I have also attached the PLC program I was running. Thanks
-
Hello, I have been so many days trying to comunicate the multiway software trought a serial usb converter with the SCU31 device, using a omron function block to read a holding register, but I can't achieved it. Now Im receiving some frames on multiway, but there is always some errors. I was wondering if somebody in here that have worked previously with modbus and omron can be able to help me in how to configure everything corectly to be able to read the value from multiway, on the plc, and where is this value saved. I'll upload some captures to show what I have done till now.
-
Looking for a little help. Replaced a 1746-NO8V analog card that hadn't been working for years and the new card is giving a Configuration Error (Module LED flashes twice, all 8 outputs are flashing 12 times). I have 2 other of the same cards in the same rack that have been working for a very long time and still working that seem to be configured the same way. Is there any way to know what is wrong with my configuration. or maybe my new card is just bad??? I have not yet swapped one of my working cards with the new card, have considered but really think I'm missing something.
